Pearl 3 Burning Amp 2023

[Toys4Boys]

Watched another YouTube re. soldering SMDs, this fellow put a light coat of solder on 1 pad, heated it and when the solder starts to melt puts the SMD in place w/ tweezers. Of course he hammers home the importance of flux! Looks to be a good way to approach them if using an iron. In an effort to be thorough, once that side sets, 2 sec or so, he solders the other leg and then comes back to the first 1.

 

[Dennis Hui]

You can sign up for notification when available on the order page:

https://diyaudiostore.com/collections/kits/products/pearl-3-phono-preamplifier

 

[SomekPoland]

ou can sign up for notification when available on the order page:

https://diyaudiostore.com/collections/kits/products/pearl-3-phono-preamplifier

I did, but it's only 11 kits. I guess they'll be gone in a blink of an eye

 

[Dennis Hui]

Just got my Pearl 3 kit in the mail... Markham Ontario.
Goodie. (and much more importantly... thank y'all)

Very nice.

I just got a duties and taxes bill notification from Canada Post. Mine's in Montreal so hopefully I'll see it in a couple of days.

 

[mhenschel]

@Dennis Hui
interesting. mine came straight through.
I'm not a volume buyer so perhaps that made a difference.

 

[Dennis Hui]

I order from the diyaudio store at most twice a year and I always get charged duties/taxes by Canada Post.
Have fun with your build!

 

[Auricle]

In message 258, Wayne said...

I have seen the future and it has matched 170's.

I wondered...

 

[6L6]

Not in the store kits, for what it's worth... Buy from Punkydawgs.

 

[SomekPoland]

Not in the store kits, for what it's worth... Buy from Punkydawgs.

What do you mean? Those kits aren't going to the store?

 

[6L6]

I mean the store kits won't have K170s. They will have K209.


There will be plenty of kits. Just be patient. Waiting for PCBs. I just received a LOT of PSU boards yesterday. It's all coming together.

 

[SomekPoland]

I mean the store kits won't have K170s. They will have K209.


There will be plenty of kits. Just be patient. Waiting for PCBs. I just received a LOT of PSU boards yesterday. It's all coming together.

Oh, now I see. It's all good. Any ETA on the kits? Even with a large margin?

 

[6L6]

Sometime between week after next and December of 2037.

 

[von Ah]

wo0t!! Final power supply build tonight!

 

[SomekPoland]

Sometime between week after next and December of 2037.

Point taken

 

[Toys4Boys]

Champing at the bit, waiting for flux and other stuff , due tomorrow

 

[Dennis Hui]

I'm hoping to have all parts ready to go before Pearl 7 comes along.

 

[jhofland]

If anyone is interested I've made a surface mount version of pearl3 with some modification in the RIAA equalization, a subsonic/supersonic filter section adapted from Doug Self's Small Signal Audio Design book and separate low noise LDO's for each channel. It all fits on a 100mm x 120mm board intended to fit in a Hammond 1455 series enclosure.

 

[rsavas]

That design could be wave soldered and easier to service if you put the smt parts on the back side and the tht stuff on the top

 

[jhofland]

At the moment, there are bottom side 100nF bypass caps for each of the op amps. You're right that it could be a bit easier to build if all the SMT were bottom side

 

[debk]

Looking at different opamp, is there any benefit of using jfet input opamps vs bjt input opamps in the Pearl 3?