Moode Audio Player for Raspberry Pi

[BackinBlack]

Try posting on the MoOde forum. Moode Forum
Any music you load on the SD card will be lost when you update MoOde.

 

[mhouston]

Can some one help. I’ve moved to 7 but can’t get my DAC to work with it. 6 etc all good.

It is a USB DAC I2S I believe. What setting do I need.

 

[mhouston]

I have selected none for a DAC but no sound. Rebooted and full **** downs, no sound.

 

[CallMeMike]

Can some one help. I’ve moved to 7 but can’t get my DAC to work with it. 6 etc all good.

It is a USB DAC I2S I believe. What setting do I need.

USB DAC I2S...?!


Why don't you try to post your issue(s) on the official forum Moode Forum ... and also supply some details about your set-up, DAC model, etc

 

[mhouston]

Yes that’s it. But the instruction say select “None”.

 

[DRONE7]

Your DAC can't be both USB and i2s.

USB plugs in with a USB cable...

i2s is a HAT DAC and sits atop a Raspberry Pi plugged to the 40 pin GPIO.

Which do you have ?

 

[mhouston]

No only USB DAC. No DAC HAT.

 

[mhouston]

Any chance of screen shots of what should be entered where?

 

[BackinBlack]

In audio settings select "None", then a little further down the page under MPD options select Edit (MPD) settings and under Volume mixer, Mixer type select "disabled" . This should give you full volume (0dB) output for your USB DAC.

 

[mhouston]

Thanks. I’ll try.

 

[mhouston]

In audio settings select "None", then a little further down the page under MPD options select Edit (MPD) settings and under Volume mixer, Mixer type select "disabled" . This should give you full volume (0dB) output for your USB DAC.

No it doesn’t work. My DAC is NOT say “Locked”. Usually it would say locked.

 

[BackinBlack]

Have you asked the question on the Moode Forum ? That's where most users discuss Moode now.
If you give the details of your DAC it would help.
Ian

 

[ErikdeBest]

I have the latest version of Moode installed and today I connected it to the DAM1021. Much to my surprise, the Moode Volume Control is now working with the DAM1021. Very very nice!

I found these threads, was this implemented in moode?
Soekris DAM1021
raw sewage

 

[TimCurtis]

I'm glad its working but no such scripts are part of moOde.

Whats the output from the commands below?

cat /proc/asound/cards

amixer

 

[Indigent Audio]

Not to confuse the issue but my pi2/moode 7.0.1/usb modi 2 volume is set to hardware and it’s working.

 

[mhouston]

No it doesn’t work. My DAC is NOT say “Locked”. Usually it would say locked.

Could not get moode 7 to work with my USB DAC. In audio left selection as None. But when going going to edit MPD a USB output does not exist.

I’ve gone back to 6.4 which works perfectly and my DCA says “Locked” and displayed bit rate and works.

 

[ErikdeBest]

I'm glad its working but no such scripts are part of moOde.

Whats the output from the commands below?

cat /proc/asound/cards

amixer

thanks for the reply!
To do that I need to hook a monitor and keyboard, and this instructions?
moode/setup.txt at master * moode-player/moode * GitHub

 

[TimCurtis]

Menu, Configure, System
SSH term server, ON
OPEN Web SSH terminal

 

[ErikdeBest]

This is what I got. Does it make any sense?

I did not do any "sound quality analysis", I am measuring the signal out with an oscilloscope due to lack of audio amplifier in my lab

 

[ErikdeBest]

Well, I think I found the answer myself. There is Software volume control, according to MPD. Let's compare it to the other volume control options I have in the music chain.

Thanks!
Erik